123 | 1 | 2 |
下载次数 | 被引频次 | 阅读次数 |
将一定配比的增黏剂、2-EHP(棕榈酸乙基己酯)和萜烯树脂进行共混,在光引发剂作用下与对氨基苯甲酸发生光异构化反应;然后将所得的产物作为硬单体、BA(丙烯酸丁酯)作为软单体、CPE(氯化聚乙烯)和PVP(聚乙烯吡咯酮)作为相容剂,采用种子乳液聚合法制备了乳液型PSA(压敏胶)。研究结果表明:当w(2-EHP)=3%、w(CPE)=1.5%和w(PVP)=6%(均相对于萜烯树脂质量而言)时,PSA的综合性能相对最佳(结构和热力学性能稳定、初粘力和持粘力适宜)。
Abstract:The tackifier,2-EHP(ethyl hexyl palmitate)and terpene resin were blended according to certainproportion,then the light isomerization reaction between above polyblend and p-aminobenzoic acid was happenedunder the action of photoinitiator.With above product as hard monomer,BA(butyl acrylate)as soft monomer,CPE(chlorinated polyethylene)and PVP(povidone)as compatibilizers,an emulsion type PSA(pressure-sensitiveadhesive)was prepared by seed emulsion polymerization method.The research results showed that the PSA had therelatively best combination property because it had the stable structure and thermodynamic property,andappropriate initial tack and holding tack when mass fractions of 2-EHP,CPE and PVP were 3%,1.5% and 6%respectively in terpene resin.
[1]杨莎,齐暑华,程博,等.压敏胶的研究进展[J].粘接,2014(3):83-86.
[2]杨玉昆,吕凤亭.压敏胶制品技术手册[M].北京:化学工业出版社,2004:13-21.
[3]尉晓丽,傅和青.改性水性丙烯酸酯压敏胶研究进展[J].化工进展,2012,31(1):176-184.
[4]胡红.丙烯酸压敏胶胶黏剂的应用[J].丙烯酸化工与应用,2000(1):35-41.
[5]房成,林中祥.乳液型丙烯酸酯压敏胶研究进展[J].中国胶粘剂,2013,22(2):40-44.
[6]李安梅.丙烯酸酯乳液型压敏胶的研究进展[J].精细化工中间体,2005,35(3):21-23.
[7]冯小平,李胜华,何伟,等.高固含量低黏度丙烯酸酯乳液压敏胶的制备[J].化学研究与应用,2010,22(11):1450-1454.
[8]宋亦兰,陈建,吴召洪,等.耐热性乳液型丙烯酸酯压敏胶的合成[J].弹性体,2012,22(6):24-27.
[9]GB/T 4852—2002压敏胶粘带初粘性试验方法(滚球法)[S].
[10]GB/T 4851—1998压敏胶粘带持粘性试验方法[S].
[11]GB/T 2792-1 998胶粘剂剥离强度试验方法[S].
基本信息:
DOI:10.13416/j.ca.2018.02.009
中图分类号:TQ436.3
引用信息:
[1]胡春玲,魏菊.异构化增黏树脂乳液型压敏胶的制备与性能研究[J].中国胶粘剂,2018,27(02):39-42.DOI:10.13416/j.ca.2018.02.009.
基金信息: